A four-point saddle is two offsets placed back to back: the conduit steps up, runs across an obstruction, and steps back down using four equal bends. If you use 30-degree bends, no chart is needed. The distance between the two bends of each offset is 2 times the obstruction height, and shrink is 1/4 inch per inch of height. This guide works from published instructions by Gardner Bender, Klein Tools and electrician-trainer Bill Bamford, not from any video.
When to use four points instead of three
Bamford's hand-bending handout describes two kinds of saddle. A three-point saddle jumps small obstructions of 6 inches or less, such as another raceway crossing yours, and is made by bending the middle bend twice the angle of the two outer bends. A four-point saddle is "made up of two equal size offset bends, bent in opposite directions" and is used to clear larger blockages than a three-point can handle. For both, all marks go on the conduit before any bending begins.
Multipliers and shrink by angle
Gardner Bender's guide lists a constant multiplier for each bender angle. Multiply the obstruction height by it to get the distance between the two bends of an offset. Shrink is the length the conduit loses per inch of height.
| Bend angle | Multiplier | Shrink per inch of height |
|---|---|---|
| 10 degrees | 6.0 | 1/16 inch |
| 22 1/2 degrees | 2.6 | 3/16 inch |
| 30 degrees | 2.0 | 1/4 inch |
| 45 degrees | 1.4 | 3/8 inch |
| 60 degrees | 1.2 | 1/2 inch |
Bamford gives the unrounded values for the same angles: 5.7588, 2.613, 2, 1.4142 and 1.1547. Thirty degrees is the easiest to do in your head, which is why his handout uses it for its examples. Shallower angles spread the bends further apart and cost less shrink; steeper angles shorten the spread but cost more shrink.
Worked example at 30 degrees
Suppose a duct is 3 inches high and 20 inches wide, and its near edge is 16 inches from the end of the conduit. This follows the layout of Bamford's own example, scaled to these dimensions.
- Distance between bends: 2 x 3 = 6 inches.
- Shrink: 3 x 1/4 = 3/4 inch.
- First mark: 16 + 3/4 = 16 3/4 inches from the end.
- Second mark: 6 inches back from the first, at 10 3/4 inches.
- Third mark: 20 inches past the first, at 36 3/4 inches.
- Fourth mark: 6 inches past the third, at 42 3/4 inches.
Mark all the way around the conduit so the line shows from any angle. Then bend 30 degrees at each mark. Between the bends of each offset you roll the conduit 180 degrees so the second bend goes the opposite way; Klein's offset steps say the same: bend the first, "spin conduit 180", then bend the second. Stop each bend when the bender's 30-degree line reaches the edge of the conduit. Klein's Angle Setter guidance warns that bending past the set angle can kink the conduit. Bamford notes that most of these bends are made off the floor and that the first bend usually goes in the opposite direction from where the conduit ends up.
To cut a stick before bending, add the shrink of each offset to the length you need. Here that is 3/4 + 3/4 = 1 1/2 inches of extra conduit.
Check the total degrees
A four-point saddle at 30 degrees spends 4 x 30 = 120 degrees. Bamford states that the NEC does not allow more than 360 degrees of bends in an EMT run, and that a pull box has to be added if more is required; he cites 358.26. NFPA public-comment text for the 2023 revision reads: "The total degrees of bends in a conduit run shall not exceed 360 degrees between pull points." Which edition and interpretation applies depends on your jurisdiction, so ask the inspector how they count offsets and saddles.
Where mistakes come from
- Shrink in the wrong place. Gardner Bender says shrinkage values are only used when working into objects, not away. Check which end of the run you are measuring from.
- Different benders. Klein's guide prints its own offset and saddle tables for its bender. Gardner Bender's and Bamford's tables agree at 30 degrees (2.0 and 1/4 inch), but the marks on your own bender decide the practical result.
- Skipping a test piece. Bend a short scrap first to confirm that your marks and the bender's angle lines agree.
Take this further with Oakgen Agent
Run Python calculations for mark positions and shrink from numbers you give it, write practice problems with answer keys, and export a pdf, docx or xlsx worksheet.
Looking for a recap of one specific YouTube video? The YouTube Summarizer does that today.
Open this task in Oakgen Agent
The prompt is filled in for you. Nothing is sent until you press send.
Frequently asked questions
What is the multiplier for a four-point saddle with 30 degree bends?
2.0 times the height of the obstruction gives the distance between the two bends of each offset, and shrink is 1/4 inch per inch of height. Gardner Bender's hand-bender guide lists 30 degrees as a constant multiplier of 2.0 with 1/4 inch of shrinkage per inch of offset depth, and Bill Bamford's handout gives the same rule of thumb: add 2 inches between marks and 1/4 inch of shrink for each inch of rise.
What is the difference between a three-point and a four-point saddle?
Bamford's handout says a three-point saddle jumps small obstructions of 6 inches or less and is made with a centre bend twice the angle of the two side bends. A four-point saddle is two equal offset bends in opposite directions with the width of the obstruction between them, and it handles larger obstructions. All marks are placed before any bending starts.
How much shrink do I add for a four-point saddle?
Shrink is calculated per offset from the height of the obstruction (1/4 inch per inch at 30 degrees). In Bamford's example the first mark is placed at the measured distance plus the shrink for one offset, and his length calculation then adds the shrink for each of the two offsets when working out how long the conduit must be before bending. Gardner Bender adds that shrinkage values are only used when working into objects, not away.
Do the bends in a saddle count toward the NEC bend limit?
The bends add up as degrees. Bamford's handout states the NEC does not allow more than 360 degrees of bends in an EMT run (he cites 358.26) and says a pull box must be added if more is needed. NFPA public-comment text for the 2023 revision reads that the total degrees of bends in a conduit run shall not exceed 360 degrees between pull points. Four 30 degree bends use 120 degrees of that total; confirm how your local inspector counts them and which edition applies.
Sources
- Gardner Bender, Hand Benders How-To Guide, 2020 (read 2026-11-19)
- Klein Tools, Conduit Bender and Angle Setter Guide, Zip Guide for offsets and saddles (hosted by ITM, read 2026-11-19)
- Bill Bamford, Bending Conduit / Tubing Using Hand Benders, Mike Holt Enterprises, 2012 (read 2026-11-19)
- NFPA, Second Draft Public Comments, NFPA 70 (2023 revision cycle), Article 358 text, 18 November 2021 (read 2026-11-19)


